Old Honeywell Thermostats vs New Models, Tower Fans vs Woozoo, Boilers vs Water Heaters: 3 Comparisons That Cost Me $4,300

I've been buying and specifying HVAC and facility equipment for seven years. In that time I've made eleven purchases I'd classify as genuine mistakes — not "could've been better," but "we ate the cost." Three of those mistakes came from the same bad habit: comparing sticker prices instead of total cost. So here are the three comparisons that keep landing in my inbox, laid out side by side.

The standard I use for all three is five-year total cost of ownership: purchase price, installation, energy, maintenance, and the realistic odds of a redo. Not the number on the quote.

1. Old Digital Honeywell Thermostats vs Newer Honeywell Models

I'm talking about the older digital units — the rectangular ones with up/down buttons and a small LCD — versus the newer programmable and connected models in the same family. Both are still out there, and the price gap is wide enough that people ask me about it constantly.

Upfront cost

Old digital units run roughly $25–60 each. Newer programmable or connected models run $80–250 depending on features (based on major U.S. retailer quotes, January 2025; verify current pricing). On a 20-unit job, that's a $1,000–$3,000 gap before you touch a single wire. That gap is real, and I'm not going to pretend it isn't.

Installation and compatibility

This is where the cheap unit stops being cheap. Many older digital thermostats were designed for two- or four-wire setups. Newer connected models typically want a C-wire for continuous power. If your building doesn't have one at the wall, you're paying an electrician to pull it — and in a finished commercial space, that's not a small line item.

In 2019 I bought 14 old digital Honeywell units for a retail fit-out because they were $38 each instead of roughly $140 for the programmable versions. I saved about $1,400 upfront. Two zones turned out to need a common wire and a different control strategy, and the rework plus a partial swap ran me $2,100. That's the whole lesson in one invoice: the cheaper thermostat cost more than the expensive one would have.

But — and this is the part that surprised me — that doesn't mean newer is always better. Here's the counterintuitive bit.

Reliability: simple sometimes wins

On low-complexity zones — storage rooms, back-of-house corridors, single-stage equipment with no scheduling needs — the old digital units have been more reliable for us than the connected models. Fewer sensors, no firmware, no app dependency, no Wi-Fi dropouts. In three years I've replaced two failed connected thermostats and zero of the old digital ones on comparable duty.

It's tempting to think newer equals more reliable. But added features add failure points, and in a mechanical room nobody's using the app anyway.

What I do now

Simple single-zone spaces get the old digital model. Multi-zone spaces, anything with scheduled occupancy, and anything a remote facilities team needs to monitor gets the newer model — and I budget the C-wire pull into the project from day one instead of discovering it later.

2. Tower Fans vs Woozoo Fans

These get compared constantly, and honestly, they're solving different problems. But people still ask me which one to buy for a workspace, so let's put them side by side.

Airflow pattern

A tower fan pushes a narrow, directional column of air. Point it at a person, and that person feels it. Point it at a room, and most of the room doesn't. Woozoo-style fans are circulation fans — they move a wider volume of air around the space rather than cooling one spot. Different job, different result.

Noise and placement

Tower fans tend to be quieter at low settings and easier to tuck into a corner near a desk. Circulation fans move more air but are usually louder at equivalent output, and they work best when placed to keep air moving through the whole room rather than aimed at a face.

Where each one fails

In 2021 I bought six tower fans for a warehouse office area — about $600 total — because they were cheap and looked tidy. The space had high ceilings and poor air movement. The tower fans cooled the three desks closest to them and did essentially nothing for the rest of the floor. We ended up adding two circulation fans anyway. That $600 wasn't wasted exactly, but it wasn't the right purchase, and I knew it within a week.

The reverse is also true: putting a circulation fan at a single workstation is a waste. It moves air everywhere except convincingly at the person who's hot.

What I do now

If one person is uncomfortable at one desk, I buy a tower fan. If a whole room feels stagnant, I buy circulation fans and place them to move air across the space. The mistake is buying one and expecting it to do the other's job.

3. Boiler vs Water Heater

These two get confused constantly, and the confusion is expensive. A boiler and a water heater are not the same machine, and swapping the terms in a purchase order has cost me real money.

What each one actually does

A boiler heats water for hydronic space heating — radiators, baseboards, radiant floors — and in many commercial systems it also supplies domestic hot water through a tank or heat exchanger. A water heater heats potable water for sinks, showers, and process use only. It does not heat the building.

If someone says "we need a new boiler" and what they actually need is hot water at the taps, you can spend five figures on the wrong appliance.

Installation and operating cost

Boilers are a bigger install: venting, piping, controls, and often a structural or mechanical-room consideration. Water heaters are simpler and cheaper to install, but they only solve the hot-water problem. According to the U.S. Department of Energy (energy.gov), water heating accounts for roughly 18% of a typical home's energy use; commercial buildings vary widely by type and occupancy, so treat that as a directional figure, not a spec.

On operating cost, the honest answer is that it depends on your building. A boiler running at low load in a mild climate can be inefficient; a properly sized water heater plus a separate heating system can beat a boiler on total cost in some small commercial spaces. That conclusion surprised me, because the conventional wisdom is always "boiler equals better."

The terminology trap

In 2023 I wrote a purchase order for a "replacement water heater" for a small office building. The building manager had said "boiler." I assumed they meant the domestic hot water unit because that's what had failed. Turns out they meant the hydronic boiler that fed the baseboards. We caught it before delivery, but the cancelled order, restocking fee, and two-week delay cost about $1,600 and a lot of goodwill.

We were using the same word and meaning different things. I now make every equipment order include a photo of the existing unit and its nameplate. It sounds excessive until it saves you a five-figure mistake.

What I do now

Before quoting either one, I confirm three things: what the unit heats (space, potable water, or both), what fuel it uses, and what the existing venting supports. Those three answers usually tell you which appliance you're actually replacing.

How I'd Decide If I Were You

None of these is a "buy the expensive one" argument. It's a "price the whole job" argument, and the whole job looks different in each case:

  • Thermostats: Old digital models win on simple single-zone spaces where nobody needs scheduling or remote access. Newer models win wherever you need multi-zone control, occupancy scheduling, or remote monitoring — as long as you budget the wiring.
  • Fans: Tower fans cool people. Circulation fans move rooms. Decide which problem you actually have before you buy.
  • Boiler vs water heater: Confirm what the unit heats before you write the order. If it only makes hot water, it's a water heater — and a boiler is the wrong answer no matter how good the price is.
My rule after seven years: the cheapest quote has cost us more in roughly 60% of cases. Not because cheap equipment is bad — because the cheap option usually pushes cost somewhere I didn't look.

Pricing and equipment figures are for general reference only and reflect quotes and invoices from my own projects; actual prices vary by vendor, specifications, region, and time of order. Verify current rates and code requirements before purchasing.

author-avatar
Gavin Mercer

Gavin Mercer covers plate, shell-and-tube, brazed-plate, and finned heat exchangers together with cooling towers, dry coolers, and evaporative fluid coolers. He applies ASME BPVC Section VIII and PED 2014/68/EU considerations while examining LMTD, overall heat-transfer coefficient, pressure drop, fouling allowance, design pressure, and approach temperature. His work guides thermal engineers and procurement teams through duty verification, material selection, cleanability, water quality, corrosion risk, and total installed cost.

Leave a Reply